Basic Weight (lbs) No valves
Valves usually mounted on the machine closer to the application,
Typically mounted behind or between 2 machines.
Can use coupled or uncoupled.
Recommended to run a continuously connected or single hose supply decoupled system.
Operator interface is a manual valve handle.
Pump located within operators reach.
1
55-9675-12-1
Recommended to run a continuously connected or single hose supply decoupled system where, the pressurized time exceeds the unpressurized time.
Operator interface is by remote pendant or can be wired into a machine controller.
NOTE: Should not be used with palletized systems as the valve is energized to unclamp. The unclamped time will be excessive, causing the valve to run hot.
2
4
55-9675-23-1
55-9675-23-2
55-9675-23-4
55-9695-23-1
55-9695-23-2
55-9695-23-4
Recommended for continuously connected "live" systems.
Always connected to the fixture by means of hoses and or rotary unions.
55-9675-16-1
55-9675-16-2
55-9675-16-4
55-9695-16-1
55-9695-16-2
55-9695-16-4
Always connected to the fixture - by means of hoses and/or rotary unions.
Center position allows no movement of clamps when the valve is de-energized.
55-9675-26-1
55-9675-26-2
55-9675-26-4
55-9695-26-1
55-9695-26-2
55-9695-26-4
Operator interface is by a manual valve handle.
Pump located within operators.
Single Acting Decoupled Systems
Valve installed with a control pendant to power systems using the Self-closing Decoupler and Tombstone Top Plates.
Commonly called a "dump pump" and uses a momentary contact pendant switch.
When preset pressure is reached the control valve automatically shifts and dumps pressure back to tank.
55-9675-25-1
55-9695-25-1
Single Acting Live systems.
Use with Manual Pallet Decouplers, Tombstone Top Plates and Self-Closing (single hose) Decouplers
NOTE all decoupled valves are de-energized when not in use to avoid heat build up between cycles.
55-9675-24-1
55-9675-24-2
55-9675-24-4
55-9695-24-1
55-9695-24-2
55-9695-24-4
Double or Single Acting run live or decoupled.
Control Auto-Shutoff Pallet Decoupler (2 hose system).
Best selection for fixture testing, runs most systems.
Reduces pressure to clamp or unclamp side of a circuit.
Use with one or two handed Auto-Shutoff Decoupler.
P-blocked center valve drops pressure in both lines. Allows decoupling and re-coupling of the hoses.
Used to operate two individual single acting systems at different pressures.
Operator interface is remote pendant or wired into a machine controller.
Double or Single Acting.
Use 1 or 2 handed Auto-Shutoff Pallet Decoupler.
Uses a P-Blocked center to drop pressure in both lines to decouple and re-couple hoses.
55-9675-27-1
55-9675-27-2
55-9675-27-4
55-9695-27-1
55-9695-27-2
55-9695-27-4
ILS559603 and ILS559604 REV B
Warning: The use of spool valves invalidates the warranty on VektorFlo® pumps.
95-5950-15
2-Hand No-Tie-Down Control Module (Decoupled Systems Only)
NOTE: Contact factory for custom pump configurations.
NOTE: Voltages listed are input to control box for pump motor. All solenoid valves use 24 VDC control voltage supplied by the transformer internal to the pump control box. Wiring of control valves supplied with pump is not required.
NOTE: Solenoid valves configurations are supplied with one valve control pendant with a 6 ft. cable. For additional pendants order from the chart.
NOTE: See pump manual to calculate the required electrical service for your specific application.
NOTE: All 115VAC single phase pumps require a 20 AMP dedicated service electrical connection for proper operation and service life.
NOTE: NOTE: 525-600V, 3-Phase pumps are available upon request
Pendant Switch Control (1 included with 1st valve of pump)
CNC Machine Control
ILS559605 REV E
Valve Wiring Cable, M12, 5 pin (add one cable per valve)
Pump/Machine Tool Interface Cable, 24 pin or 36 pin, Single Connection
Contact your sales representative for details.
ILS559606 REV E