Hydraulic

Top Flange/Manifold Mount VersaCam™ Swing Clamp Specifications

WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation.

** Cylinder capacities are listed at 5,000 psi maximum operating pressure, with a standard length VektorFlo^® arm installed. Minimum operating pressure is 750 psi for single acting, 500 psi for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application, divide the cylinder capacity shown above by 5,000, and multiply the Resultant Number X Your System Operating Pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, frictional loss, and/or return springs.)

*** To allow for piece part height variations, it is recommended that the vertical travel be set at about 50% of the vertical stroke.

**** To insure maximum service life and trouble-free operation, restrict fluid flow to the level indicated in the Clamp Time and Fluid Flow Rate Chart.

*****In-Port Valves require the use of manifold mount ports.

All dimensions are in inches.

Top Flange/Manifold Mount VersaCam™ Swing Clamp

Easy to use, just bolt in place and plumb or use the easy to make manifold pattern to eliminate external plumbing Available in four capacities from 450 to 5,000 lb. Can be either manifold mounted or standard plumbed using standard SAE fittings Single piece body and mounting give a rigid installation, no threads to rock around or additional mounting hardware to buy Fitting 30-8711-20 adapter assembly included with the clamp. Plugs are also included and shipped. Standard Arm Clocking feature uses standard Vektek Arms. Arms sold separately. To avoid cylinder damage and preserve warranty, observe flow rate limits and time calculations. Optional In-Port Flow Control is a meter-in device with reverse free flow check valve. Optional In-Port Sequence valve is a sequencing device with reverse free flow check valve.

Hardened V-cam tracks resist damage and give you a built in extra cam (opposite swing direction) or straight-line option should you accidentally damage one. Specify right, left or straight cam, we will preset the swing when you order Low installed clamping height can be fine tuned to fit your part with easy to make spacers

Top Flange/Manifold Mount VersaCam™ Swing Clamp Dimensions

All dimensions are in inches.

Top Flange/Manifold Mount VersaCam™ Swing Clamp Mounting Specifications

	For proper sealing, mating surface must be flat within 0.003 with a maximum 63 µin Ra surface finish.
Mounting Specifications Model No. ØA ±.010 B C ±.005 D ±.005 E ±.005 F ±.010 G ±.010 15-6X05-00-X 1.015 10-32 0.795 0.219 0.687 0.438 0.625 15-6X09-00-X 1.453 1/4-20 1.032 0.344 0.875 0.562 0.844 15-6X13-00-X 1.765 5/16-18 1.250 0.438 1.000 0.531 1.047 15-6X18-00-X 2.390 3/8-16 1.719 0.601 1.367 0.750 1.406

 All dimensions are in inches.

Top Flange Swing Clamp Spacers, Capacities below 5,000 lb. Model No. Swing Clamp Model No. TuffCam™ Model No. Capacity A B C D E F 64-0409-01 15-XX05-00 14-6X05-01 450 1.45 1.88 1.02 28 1.02 0.75 64-0414-01 15-XX09-08 14-6X09-01 1100 1.97 2.31 1.45 28 1.32 1.25 64-0417-01 15-XX13-11 14-6X13-XX 2600 2.45 2.69 1.77 28 1.63 1.25

NOTE:

• Customer will be required to cut spacer to length and install mounting and oil feed holes as needed.

• Material is extruded aluminum alloy